Applications |
NiMH battery is made of 12 pcs NiMH sub C 3300mAh cells and packed in 2×6 configuration, high powerr type, for iRobot Roomba 4905, 400 |
Features |
- This NiMH Box Battery is compatible with all Roomba FloorVac models and has 11% more running time than the OEM battery pack. Compatible with the following models:
- iRobot Roomba 400 Series (Model #: 4230, 4110, 4225, 4910, 4330)
- Discovery Series
- Create Models
- Dirt Dog Models
- Provides up to 100 minutes of run time
- 50 percent greater useful life than original Roomba batteries
- Easy to charge and connect
- Can be recharged up to 1000 cycles
|
Voltage |
Voltage:14.4 (working), 17V ( peak), 12V ( min.) |
Capacity |
3300mAh, 47.52Wh, |
Protection |
10K @ 25C thermistor installed in the battery pack. Power will be cut off if battery temperature is above 70oC during charging to prevent from over charge. |
Prewired
|
- RB-ROOMBA400: Battery With yellow enclosure included
-
- Tab Charging terminal. (Right most = Positive)

- RB-HSC12R2WR33: Battery Only, No yellow enclosure included
- Charging / Discharging Terminals: 6″ length Open End Wires
- RB-ROOMBA400C01: BAttery Charger recommended
- 1 pcs Multi-Current Universal Smart Charger for 9.6V – 18V NiMH Battery Packs (Tamiya Plug) , UL Listed (CH-UN180)
- 2.2 hrs charging time by 1.8A charging current
- Due to the internal temperature sensor (white wire) installed inside the pack, Please don’t connect charger’s temperature sensor wirefrom the charger to battery.
- 1 pcs Connector/Adaptor: From Standard Male Tamiya to 10mmx6.3mmx0.8mm tab
- Utilize for connect between CH-UN180 charger and battery while charging.
- Red wire = positive
- Black wire = negative
- Tabs dimension(LxWxH): 10mm(0.4″)x6.3mm(0.2″)x0.8mm(0.03″)
|
Max. Discharging rate |
4.2A limited by polyswitch |
Related Products |
For a faster charging, You may charge the pack by Multi-Current Universal Smart Charger for 9.6V – 18V NiMH Battery Packs (Tamiya Plug) , UL Listed (CH-UN180) + connector adapter
- 2.2 hrs charging time by 1.8A charging current
- Due to the internal temperature sensor (white wire) installed inside the pack, Please don’t connect charger’s temperature sensor wire from the charger to battery.
|
Battery Dimensions(LxWxH) |
5.35″ (136mm) x 1.77″ (45 mm) x 1.77″ (45 mm) |
Battery Box Dimensions(LxWxH) |
7.09″ (180mm) x 2.0″ (52mm) x 2.1″ (53mm) |
Battery Weight
|
714g ( 25.2 Oz.) |
Battery w/ Box Weight |
38.5Oz (1091 grams) |
Warnings |
- Please never short circuit the battery
- Do not discharge the battery pack below 12V ( 1.0 V / cell). Deep discharging may damage NiMH battery pack.
- Please check and match the polarity of our connector to your device. We are NOT liable for any damage to your device due to reverse polarity
|
How to Change inside battery |
- The most troubles of Irobot was caused by dead battery because OEM did not use a high quality cell. You shall try to replace a inside battery pack before throw it away , as the following picture — It is easy and fast
- There are some battery case that is glue shut. You have to exercise caution on pry open the case as we are not responsible for any damage to the case
|
Tipes |
NiMH battery is of the best safety, and environmentally friendly. |